Camera Finder: Apple: Iphone 4 Review, Review: Iphone 4: Image Quality

  -  

Note: Removing the battery allows better access khổng lồ the plate covering the rear camera"s connector. However, it is not absolutely necessary khổng lồ remove the battery. If your battery is particularly difficult khổng lồ remove, leave it in & work around it.

Bạn đang xem: Camera finder: apple: iphone 4 review, review: iphone 4: image quality





Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.


*


Pinch the rear panel with your fingers và lift it away from the iPhone. Alternatively, use a Small Suction Cup .


Use a plastic opening tool to gently pry the battery connector up from its socket on the xúc tích board.


Pry from the top và bottom of the connector bracket—there isn"t as much of an overhang on the sides, and you may damage the connector.


Be very careful to lớn only pry up on the battery connector và not the socket on the xúc tích board. If you pry up on the súc tích board socket, you may break it entirely.


If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to lớn release the adhesive.


Prying in other places may cause damage. Don"t try khổng lồ forcefully lever the battery out. If needed, apply a few more drops of alcohol khổng lồ further weaken the adhesive. Never deform or puncture the battery with your pry tool.


If there"s any alcohol solution remaining in the phone, carefully wipe it off or allow it khổng lồ air dry before installing your new battery.


If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.


Before reconnecting the battery connector, be sure the contact đoạn clip (shown in red) is properly positioned next lớn the battery connector.

Xem thêm: Khắc Phục Samsung Galaxy J7 Pro Lỗi Camera Trước, Mẹo Xử Lý Samsung J7 Pro Lỗi Camera Sau Hiệu Quả


Before reassembly, clean metal-to-metal tương tác points with a de-greaser such as windex. The oils from your fingers have the potential to lớn cause wireless interference issues.


Use an iPod opening tool to lớn slightly lift the đứng top edge of the connector cover away from the lô ghích board.


Before reassembly, be sure khổng lồ clean all metal-to-metal liên hệ points on the connector cover with a de-greaser such as windex. The oils on your fingers have the potential to cause wireless interference issues.


Give the author +30 points! You're Finished!

Cancel: I did not complete this guide.

193 other people completed this guide.


This was super simple. My camera was not focusing after a previous company replaced it due lớn a faulty flash. I decided to take things into my own hands...no pun intended.

The instructions are super simple và easy to follow. Be aware of the loose video under the connector - mine flew out - và I was worried I wouldn"t figure out how lớn get it back in.

I also had lớn use a #0 screwdriver...#00 was too large.

I couldn"t get the battery out...so, I was just super careful that the phone was off, & remained off during the repair.

Out with the defective camera...in with the functioning camera...replaced a couple of screws & the battery connector. Tested the camera prior to replacing everything.

Thank you 6struyenky.vn!

You ROCK!!!


TechxaSolutions - Sep 7, 2012 Reply


great comment!. You Rock!


Luca - Jan 25, năm 2016


Hi guys. I just did it ! I would not describe it as super easy, but thanks khổng lồ the screw template provided file, even the now famous pressure tương tác can not be lost ;-)

I just wanted to comment, not only to praise 6struyenky.vn (and myself), but also lớn mention two side effects I had to lớn overcome:

-First, when finished, the power nguồn button did not work (I had lớn plug the Dock Connector to lớn start the phone). As I the power button is not so far from the rear camera, I figured out something went wrong in the reassembly. Since I had just done it once, I thought I could do it a second time, so I removed the newly assembled camera and reassembled it with extra caution. At the end, the power button worked as expected.

-Second: each time I restarted the phone after reassembly (twice, then), the SIM card would not unlock after the pin sạc code was entered. I had khổng lồ remove and reinsert the SIM thẻ for the pin sạc code khổng lồ finally unlock it.

Xem thêm: Opinions On Ran, The Dark Rakshasa : Summonerswar, Rakshasa (Dark)

Otherwise, everything went smoothly, thanks again lớn the 6struyenky.vn guys !


tibomartinperso - Jan 17, 2013 Reply


Fantastic!!! my problem was the rear camera, when i switch on the camera app the screen were completely black and the torch was not working at all! I buyed the tools and the rear camera everything arrived here in Italy in perfect time as scheduled và in one hour I did the job !!! now my iphone camera is perfectly up and running !!! thanks khổng lồ 6struyenky.vn and their guides!


vflip - Jan 3, 2014 Reply


hello guys ! I have done the replacement correctly because my camera wasn"t able to lớn focus anymore ! But now the flash light isn"t working anymore :(( what can i do ?

Sincerly,

Antoine


antoinevalen - Feb 24, 2014 Reply


Load more comments
add Comment

1024


Cancel Post comment

Embed this guide

Choose a kích cỡ and copy the code below to lớn embed this guide as a small widget on your site / forum.


Single Step Full Guide
Small - 600px Medium - 800px Large - 1200px

Preview


View Statistics:

Past 24 Hours: 4